Categories
Equipment Fitness Training

Garmin Frustrations

I haven’t been able to upload my fitness activities from my Garmin 910XT in several months. My last activity that made it through wasn’t even a proper run, it was my timer event for when my brother was running a half marathon, so that I would be ready and waiting for Photo opportunities when he approached the finish line. That was back in June 2015.

After uploading that file I did a firmware update to the 910. Why? I am hoping they will fix the bug that has my barometer all messed up, and I would really like the option to turn off the barometer and work off GPS altitude alone. This has been an issue from about 7 months after purchase. My altitude starts at the correct 4000 feet and then sky rockets to 40,000 feet over the next minute because the barometer takes over. So I have been without elevation data most of the time I have owned it. Not that I really care, but it an option that is nice to see.

Ever since that firmware update, my data uploads will not complete. My computer connects and recognizes the watch, the ANT+ senses its there. It goes through the upload process and the watch finishes its side of the comunication. But the computer side always hangs. And after hours of waiting I usually have to force the program to close, which it then warns that I may loose data. Well the data is already gone because the watch says its done? WTF? nothing shows up on the webpage.

What have I tried?

  • Reinstalling firmware
  • Reinstalling Garmin Express
  • Fooling around with the communicator settings
  • Deleting My 910XT from the account and then re-aquiring it with the software
  • Upload full data set

Not sure what else to try because everything looks like its working, its like the computer is waiting for one more small piece of info from the watch to complete the cycle. A power off type of simple command that never comes.

Ugh, off to contact tech support.

 

Categories
Aviation Maintenance

Setup for success? I think not.

This is what it looks like when the electric propeller heat is active on the ground with no propeller movement:

IMG_0885

Burning rubber and 8 composite blades destroyed.

The electric heaters installed on most IFR rated aircraft propellers can crank out a ton of energy in order to keep up with the extreme cold found at altitude. The heat will melt off any accumulated ice and prevent further ice from forming. Ice on propellers is a bad thing for two reasons; it reduces the thrust efficiency of the propeller, and, it creates an imbalance that can cause propeller and engine damage. That same heat will do damage to the propeller if there isn’t sufficient cooling available.

Normal operations would have the propeller heat switch in the OFF positions at all times, except when you want the prop heat applied during icing conditions at altitude. Unfortunately that switch was left ON in this situation.

Now, there is also fail safe in the scenario to prevent this expensive repair from happening. Normally the prop heat will only operate when a pressure switch senses that you have oil pressure on the affiliated engine, hence a running engine, thus the prop is supposed to be moving and can provide some cooling to itself via the air it is slicing through. So there are two switches that must be activated for the prop heat to operate, one is automatic and senses oil pressure, and the other is human controlled.

So what went wrong here? Although this aircraft is fairly new to the fleet, there are many more like it within the fleet, so this is not a problem with personnel being unfamiliar with aircraft systems.

Further investigation found that the pressure switch had failed at some time in its past history. In order to make the system operational again, the pressure switch was bypassed or hot wired. This means that the system will now apply heat to the propellers without the engines running. The safety has been bypassed, which means its up to personnel to ensure the switch is always OFF. Not really a bad thing as long as you remember to turn it off….right?

This is what I like to call “being setup for failure”. No one intended to fry the props. However a safety was bypassed to keep the operation rolling. Stress happens and the fragile human brain forgets to fix that hot-wire job when the aircraft returns from its flight. Time passes and the aircraft is sold. New operator has no immediate knowledge of the potential problem and all systems appear to work. All your waiting for now is the right combination of forgetful human nature and WHOOF, you have two cooked props.

So what are the lessons that can be learned from this expensive and sad situation:

  1. Always follow the pilots check list – the check list is there to make sure your brain doesn’t forget any steps, like turning off things that have potential to do damage.
  2. Always follow the full maintenance procedure – A full blown functional check of the prop heat should have found this fault before it caused damage, never trust the guy who did the job before you.
  3. Fix the problem the first time – Procrastinating only causes more problems in the long run, the pressure switch is small and cheap when compared to the propeller it is protecting.
  4. Prepare for the worst – Always check that the cockpit switches and circuit breakers are in the normal or power down positions BEFORE you apply ground power to the aircraft.

At the end of the day, everyone is responsible for their actions. If each of us endeavor to do the job right the first time, we greatly reduce the risk of failure. Every time we take a short cut, or skip steps, we increase the likely hood that something will go wrong. Then all it takes is time…and eventually it will go wrong.

Does this sound familiar – “We never seem to have time to fix it properly right now, but we always have plenty of time to fool around with it over and over again for the next 3 weeks.”

Lets remember to “Setup our colleagues for success…not failure”

Categories
Pirates Projects Real Life

Yar, there be treasure…

So the epic treasure hunt of our 2015 family camping trip / reunion was a total success. Although it had a rocky start, the kids found the booty at the end of the map.

 

Treasure
Lots of fun, and I will be making a video documentary of the whole event. There will also be a separate area on this webpage dedicated to the event, due to the immense amount of effort put in by my brothers and I.